The integrated hardware designs always requires improvement in performance, reduction in power consumption and semiconductor die area which is needed for the cost of reduced modularity and replace ability of components in IC hence to accompanish this MYD-Y7Z010/007S is evolved.
The MYD-Y7Z010/007S development board is powered by Xilinx XC7Z007S (Zynq-7007S) or XC7Z010 (Zynq-7010) SoC device.
The MYD-Y7Z010/007S development board employs the MYC-Y7Z010/007S as the controller board by populating the CPU Module on its base board through 1.27mm pitch 180-pin stamp-hole (Castellated-Hole) interface, allowing users to take the advantages of numerous extended out signals. Core component on CPU module including Z-7010 or Z-7007s processor, 512MB DDR3 SDRAM, 4GB eMMC, 16MBQSPI Flash, Gigabit Ethernet PHY and external watchdog.
Let’s have a look at important features of MYD-Y7Z010/007S
- MYC-Y7Z010/007S CPU Module as Controller Board
- 667MHz Xilinx XC7Z010 or XC7Z007S ARM Cortex-A9 Processor with Xilinx 7-series FPGA logic
- 512MB DDR3, 4GB eMMC Flash, 16MB QSPI Flash
- USB Host, 3 x Gigabit Ethernet, RS232, RS485, CAN, TF, GPIO…
- Optional LCD/Camera Modules and IO Extension Cape
- Ready-to-Run Linux 3.15.0
- Supports -40 to +85 Celsius Extended Temperature Operation for Industrial Application
Additionally, the MYD-Y7Z010/007S development board takes full features of the Z-7010 or Z-7007S all programmable SoC to create a rich set of peripherals to the base board through headers and connectors including RS232, RS485, USB Host, three Gigabit Ethernet ports, CAN, TF card slot, JTAG as well as one 2.54mm pitch 2 x 25-pin expansion header to let more GPIOs available for further extension.
The MYD-Y7Z010/007S Controller Board (MYC-Y7Z010/007S CPU Module)
MYC-Y7Z010/007S CPU Module
MYIR has designed an IO expansion board MYD-Y7Z010/007S IO Cape to connect to the MYD-Y7Z010/007S development board via the 2.54mm pitch 2 x 25-pin expansion header to expand and enhances its functionality with added peripherals and signals including HDMI, Camera, LCD and Pmods.
Features :
Mechanical Parameters
- Dimensions: 153mm x 80mm (base board), 75mm x 50mm (CPU Module)
- PCB layers: 4-layer design (base board), 10-layer design (CPU Module)
- Power supply: 12V/2A
- Working temp.: -40~85 Celsius (industrial grade)
SoC
- Xilinx XC7Z010-1CLG400I (Zynq-7010) or XC7Z007S-1CLG400I (Zynq-7007S) ARM® Cortex™-A9 MPCore processo
– 667MHz dual-core processor (up to 866MHz, for XC7Z010)
– 667MHz single-core processor (up to 766MHz, for XC7Z007S)
– Integrated Artix-7 class FPGA subsystem
with 28K logic cells, 17,600 LUTs, 80 DSP slices (for XC7Z010)
with 23K logic cells, 14,400 LUTs, 66DSP slices (for XC7Z007S)
– NEON™ & Single / Double Precision Floating Point for each processor
– Supports a Variety of Static and Dynamic Memory Interfaces
Memory
- 512MB DDR3
- 4GB eMMC
- 16MB QSPI Flash
Peripherals and Signals Routed to Pins
- 10/100/1000M Ethernet PHY
- External watchdog
- Three LEDs
– One red LED for power indicator
– One green LED for FPGA program done indicator
– One flashing green LED for system indicator
- 1.27mm 180-pin expansion connectors bring out below signals:
– One Gigabit Ethernet
– One USB OTG 2.0
– Two Serial ports
– Two I2C
– Two CAN BUS - Serial ports, I2C and CAN signals will be reused in PS part, or implemented through PL pins
– Two SPI (can be implemented through PL pins)
– ADC (one independent differential ADC, 16-channel ADC brought out through PL pins)
– One SDIO
The MYD-Y7Z010/007S Base Board (MYB-Y7Z010/007S)
PS Unit
- One USB Host
- One RS232 serial port (with isolation)
- One RS485 (with isolation)
- One TF card slot
- One CAN interface (with isolation)
- One 10/100/1000Mbps Ethernet interface
- One 2.54mm pitch 14-pin JTAG interface
- One Debug serial port (UART)
PL Unit
- One 2.54mm pitch 2 x 25-pin GPIO expansion header
- Two 10/100/1000Mbps Ethernet interfaces
- Three user LEDs
It is a cost-effective and high-performance solution for industrial application such as Industrial Ethernet, machine vision, PLC/HMI and etc. The board is ready to run Linux and supports industrial operating temperature ranging from -40 to +85 Celsius.
The 4.3- and 7-inch LCD Modules as well as MY-CAM011B camera module from MYIR can be supported through the MYD-Y7Z010/007S IO Cape. Optional USB Wi-Fi and Camera modules are also provided. With all these features, the MYD-Y7Z010/007S board is not only great for integration into custom design, but also can be used as a stand-alone development board for evaluating solutions based on Xilinx Zynq-7000.
At last let me conclude by providing little information about how we are related to this product, as you all know Tenet addresses the needs of large multinationals, governments, defense, educational, research institutions, artists and hobbyists in various domains inclusive of but not limited to physical computing, automotive, electronics, embedded systems, sensor networks and many more.
In this abiding endeavor of keeping our customers happy in bringing the new products, Tenet Technetronics is more than happy to set up an Authorized Distribution Alliance with MYIR tech and promote as well as distribute the MYIR tech products in India
Continued with this, there are a lot of activities (Workshops/Videos/Application notes) please stay tuned with our YouTube channel as well as blogs to learn more. (Website: https://www.tenettech.com/browse/myirtech)
For any further assistance, please feel free to contact us at info@tenettech.com and we would be more than happy to help.
To Buy : https://www.tenettech.com/product/myc-y7z010007s-cpu-module-1
